SmartgridOne logo
SmartgridOne logo
AppCertifikat
Nya integrationerÖversikt
a-TroniXABB, FIMERABB, FIMERABB, FIMERABB, FIMERABB, FIMERABB, FIMERABB, FIMERABB, FIMERABB, FIMERABB, FIMERABB, FIMERABB, FIMERADS-TecAforeAlphaESSAmpowrAngileAnklous PV, hybrida och batteriomvandlareAPsystemsAteps Batteri
Autarco
BeauventC-BatteriCellpowerChisageDanfossDeltaDET Power PV, Hybrid och BatteriinverterDEYEDiehl-AkoDMEGC VäxelriktareDynessDysun EnergyEcosourcenEenovanceElecnovaEnbrilionEnergreenEnerlutionEnjoyPowersEnphaseEP UtrustningESY-växelriktareFortona
FraxFroniusGoodWeGotionGrönare / Alfen
HiteHithium
Hypontech
All In One ESSHybrid Inverters
iWellJinkoKacoKehuaKostal
MarstekMastervoltMidTeQMotomaOctave EnergyOmniPowerPixiiPower-SonicPoweroadPylontechRefurbRegitecRenonRitarSAJSchneider SunEzySchucoSCUSE2200H till SE6000HSessySigenergySinexcel
Socomec
SolarlogSolarMaxSolarwattSolaxSolinteg
Solis
Solplanet
SunwaytechSunwoda
Sus-PowerTeclomanTeploreTesvoltVaconVictronVolstoraWattsNextWeihengXantrexZeversolar
Installation
Kontrollera svarstidLicensNätverkRiktlinjer för ledningsdragning och anslutningSäkerhet, underhåll och juridiska meddelandenSnabbstartSpecifikationerStatus LED-lampor
Videohandledningar
EnheterPV hybrid and battery invertersHYXiPOWER
logotyp

Stödda Enheter

Device TypeVariantsManualModbus TCP (Ethernet)RS485Curtailment
All In One ESSHYX-H6K-HTAManual❌✅✅
HYX-H9K-HTA
HYX-H12K-HTA
HYX-H15K-HTA

Koppling

RS485

Hypontech

Previous Page

Hybrid Inverters

Next Page

On this page

Stödda EnheterKopplingRS485

För RS485-koppling, använd COM-porten (N° 5) på växelriktaren.

Info
RS485 Wiring
  • For correct RS485 wiring: Follow the guidelines for RS485 wiring.
  • If the wiring shown in the table below is incorrect, please let us know.
  • There is no general consensus in the industry about the usage of A and B for the RS485 polarity, so it may be counterintuitive and opposite of what you might expect for some devices.
DeviceSmartgridOne Controller model OM1SmartgridOne Controller model IG8RS485-USB converterRS485-Ethernet converter
RS485 A (Pin 5)RS485 ARS485_POSRS485 ATX+
RS485 B (Pin 6)RS485 BRS485_NEGRS485 BTX-
N/ARS GNDGNDNot availableG
Varning
NOTE: RS485 Device Addresses
  • You MUST give each device on the RS485 bus a unique address. Check the manual of the device on how to do this.
  • Use lower addresses first (1, 2, ...) because the SmartgridOne Controller will find them faster!
  • For each device, it is generally recommended to stick with the factory default baud rate, parity, and stop bits. The SmartgridOne Controller will scan on those first.