SmartgridOne logo
SmartgridOne logo
Accesorios
AplicaciónAvisos de seguridad, mantenimiento y legales
Caja de herramientas
Certificados
Configuración de la A a la Z
ControladorDirectrices de cableado y conectividad
Dispositivos
Bomba de Calor
Caldera
Cargas conmutable
Estación de Carga para Vehículos Eléctricos
Inversores Híbridos FV y de Batería
a-TroniXABB, FIMERADS-TecAforeAlphaESSAmpowrAngularAPsystems
Autarco
Batería AtepsBeauventC-BateríaCellpowerChisajeDanfossDeltaDEYEDibujarDiehl-AkoDynessDysun EnergyEcosourcenEenovanceElecnovaEnbrilionEnergreenEnerlutionEnjoyPowersEnphaseEquipo EPEVEFortona
Foxess
FraxFroniusGoodWeGotionGreener / Alfen
Growatt
HiteHithium
Huawei
Hypontech
Hyxipower
Inversores DMEGCInversores ESYInversores Fotovoltaicos, Híbridos y de Batería AnklousInversores FV, Híbridos y de Batería DET PoweriWellJinkoKacoKehuaKostal
Kstar
MarstekMastervoltMidTeQMotomaOctave EnergyOmniPowerPixiiPower-SonicPoweroadPylontechRCT PowerReacondicionamientoRegitecRenonSAJSchneider SunEzySchucoSCUSE2200H a SE6000HSessySigenergySinexcel
Sma
Socomec
Sofar
HYD 3000…6000-ESPowerMagicSeries TL-G3 y TLM/X-G3
Solaredge
SolarlogSolarMaxSolarwattSolaxSolinteg
Solis
Solplanet
Sungrow
SunwaytechSunwoda
Sunwoda
Sus-PowerTeclomanTeploreTesvoltVaconVictronVolstoraWattsNextWeihengXantrexZendure SolarFlowZetaraZeversolar
Medidor de agua
Medidor de Energía
Medidor de Gas
Nube
Nuevas integraciones
Plc
Especificaciones
Específico del Cliente
Inicio rápidoInstalaciónLEDs de estadoLicenciaRed
Resolución de problemas
Señales Externas
Tiempo de respuesta de controlTutoriales en video
DispositivosInversores Híbridos FV y de BateríaSofar

TODO: ¿Parece que esto es válido para más inversores?

logo

Inversores Sofar TL-G3 y Series TLM/X-G3

Dispositivos compatibles

Device TypeModbus TCP (Ethernet)RS485Curtailment
...✅✅✅
Advertencia
Advertencia
  • La mayoría de los dispositivos pueden comunicarse usando modbus TCP. Esto no es válido para la serie "SOFAR 1...40KTL"
  • Algunos inversores requieren firmware específico que está limitado a ciertos distribuidores. Consulte a su distribuidor en caso de dudas.
Image

Cableado

Ethernet

PowerMagic

Previous Page

Solaredge

Next Page

On this page

Inversores Sofar TL-G3 y Series TLM/X-G3Dispositivos compatiblesCableadoEthernetRS485...TL-G3 & G1 & G2...TLX & TLMConfiguraciónRS485

Conecte el inversor a su red de internet usando el "SOFAR SOLAR ETHERNET STICK LSE3".

Para un cableado correcto de ethernet: Siga las directrices para el cableado ethernet.

RS485

...TL-G3 & G1 & G2

Info
RS485 Wiring
  • For correct RS485 wiring: Follow the guidelines for RS485 wiring.
  • If the wiring shown in the table below is incorrect, please let us know.
  • There is no general consensus in the industry about the usage of A and B for the RS485 polarity, so it may be counterintuitive and opposite of what you might expect for some devices.
DeviceSmartgridOne Controller model OM1SmartgridOne Controller model IG8RS485-USB converterRS485-Ethernet converter
RS485s TR+RS485 ARS485_POSRS485 ATX+
RS485s TR-RS485 BRS485_NEGRS485 BTX-
N/ARS GNDGNDNot availableG
Image

...TLX & TLM

Info
RS485 Wiring
  • For correct RS485 wiring: Follow the guidelines for RS485 wiring.
  • If the wiring shown in the table below is incorrect, please let us know.
  • There is no general consensus in the industry about the usage of A and B for the RS485 polarity, so it may be counterintuitive and opposite of what you might expect for some devices.
DeviceSmartgridOne Controller model OM1SmartgridOne Controller model IG8RS485-USB converterRS485-Ethernet converter
RS485s TR+ (pin 1)RS485 ARS485_POSRS485 ATX+
RS485s TR- (pin 3)RS485 BRS485_NEGRS485 BTX-
N/ARS GNDGNDNot availableG
Image

Configuración

RS485

Advertencia
NOTE: RS485 Device Addresses
  • You MUST give each device on the RS485 bus a unique address. Check the manual of the device on how to do this.
  • Use lower addresses first (1, 2, ...) because the SmartgridOne Controller will find them faster!
  • For each device, it is generally recommended to stick with the factory default baud rate, parity, and stop bits. The SmartgridOne Controller will scan on those first.

El control externo del inversor debe activarse en el menú de configuración del inversor a través de la pantalla LCD.

  1. Pulse brevemente el botón hacia abajo.
  2. Verá "1. Enter settings", mantenga pulsado el botón hacia abajo durante 2 segundos para entrar en la configuración.
  3. Navegue por la configuración hasta que vea:
    • Modbus Address o
    • Set ComProtocol
  4. Mantenga pulsado el botón hacia abajo durante 2 segundos para establecer la dirección.
  5. Ajuste la dirección al valor deseado.